Roadmaps / BeagleBone / Setup and lab safety
Read first
Setup and lab safety
Order the board first. Lead times vary: in early 2026 Mouser listed a 12-week factory lead time for the BeagleBone Black Industrial variant, and the standard Rev C board was in stock at some sellers and back-ordered at others. Check stock before you plan Week 1.
| Item | Why you need it | Typical price (estimate) | Needed? |
|---|---|---|---|
| BeagleBone Black Rev C (AM3358, 512 MB RAM, 4 GB eMMC) | The board. | US$60 to 110; prices vary widely by seller (checked 22 Nov 2026) | Yes |
| microSD card, 16 GB or larger | Boot, recovery and update drills | $8 | Yes |
| 3.3 V USB-to-serial cable for the 6-pin debug header | A console that works when the network does not | $15 to 25 | Yes |
| 5 V, 2 A power supply for the barrel jack | USB power alone can reset the board under load | $8 | Yes |
| Breadboard, jumper wires, two push buttons, LEDs and resistors | Loopback wiring and the limit switch | $12 | Yes |
| Ethernet cable | Network access and updates | $4 | Yes |
| 8-channel USB logic analyzer that works with sigrok (typically 24 MHz sampling, about 40 ns resolution) | An independent check of step timing at the 1 µs budget | $12 | Yes |
| I2C temperature or humidity sensor breakout (for example a BME280 or TMP102 class) | Week 6 and Phase 2 project 1 | $5 | Yes |
| 5 V relay module or USB-controlled relay in the supply line | Repeatable power cuts in Phase 4, driven from your laptop | $10 | Yes, from Week 13 |
| Stepper driver module (A4988 or DRV8825 class), NEMA 17 stepper motor, 12 V supply | Moves real hardware. Check that your module accepts 3.3 V STEP and DIR levels (an A4988 takes its logic supply from VDD: use 3.3 V). | $35 to 45 | Optional |
The minimum kit (everything marked Yes, analyzer included) is about US$135 to 195 depending on the board price. Everything in the milestone works in loopback mode without the motor. A PocketBeagle (original) has the same AM335x PRUs in a smaller board. The newer PocketBeagle 2 uses a different chip (TI AM62x family, about US$29) with a dual- or quad-core Arm Cortex-A53, a Cortex-M4F core and a PRU subsystem. The PRU idea carries over, but the firmware, memory map and toolchain differ from the AM335x, so Phase 3 does not run on it unchanged. Use it for the port estimate in the Week 15 memo.
| Risk | Rule |
|---|---|
| Wrong voltage destroys a pin | Header pins are 3.3 V and not 5 V tolerant. Read the board manual before wiring any 5 V signal. |
| Motor supply damages the board | Power the motor driver from its own supply, share ground only, and never draw motor current from the header. Set the driver's current limit before you connect the motor. |
| Lost work | In Phases 1 to 3 flash only the microSD card and keep the eMMC image as your known-good fallback. Back up the eMMC image before Phase 4, where ADR-5 decides what boots from where. |
| Wrong memory write hangs the board | Avoid writing /dev/mem by hand. Use remoteproc, RPMsg and kernel interfaces. |
| Power-cut drills corrupt storage | Run them on a sacrificial microSD card (and a backed-up eMMC), on your own board only, through the relay. |
| Security | The BeagleBone Black has a general-purpose (GP) AM335x. It cannot do hardware secure boot. Plan for signed updates and a small attack surface instead (Week 15). |